GUNNER'S MATE (GM)
Note: Below are listed responsibilities for grades E-4 (3) and E-7 (c) for this job. Paygrades E-1 through E-3 assist in these tasks
GM3
A. WEAPONS SYSTEMS OPERATIONS
A4.001 PERFORM PREFIRE AND POSTFIRE CHECKS
A4.002 CHECK FOR OBSTRUCTIONS IN GUN BARRELS BY PASSING
A BORE PLUG GAUGE, AND THEN MEASURE GUN BARREL
WEAR WITH A PROJECTILE SEATING AND DISTANCE
GAUGE
A4.003 TEST FIRING CUTOUT ASSEMBLIES
A4.004 OPERATE THE COMPONENTS OF THE MK 41, MK 13, AND
MK 26 GUIDED MISSILE LAUNCHING SYSTEMS
A4.005 PERFORM (AMOT) TEST ON LAUNCHERS
A4.006 TEST FUZE-SETTING DEVICE OPERATION
A4.007 CONDUCT OPERABILITY TEST: OCSOT, CSOT, AND DSOT
ON GUN MOUNTS AND LAUNCHERS
A4.008 CLEAR MISFIRED ROUNDS FROM A GUN
A4.009 APPLY COMMAND CRITERIA FOR EMERGENCY FIRING AND
DUD JETTISONING
B. WEAPON SYSTEMS/COMPONENTS MAINTENANCE
B4.001 INVENTORY GUN MOUNT SPECIAL TOOLS, EQUIPMENT,
AND CLEARING CHARGES NECESSARY FOR FIRING
B4.002 INSTALL ALIGNMENT EQUIPMENT ON LAUNCHING SYSTEMS
B4.003 INSTALL, ALIGN, AND USE A BORE SIGHT TELESCOPE,
USE A TRAM BAR
B4.004 USE AND MAINTAIN COMMON SPECIAL TOOLS
B4.005 PERFORM PREVENTIVE MAINTENANCE ON LAUNCHING
SYSTEMS AND HANDLING EQUIPMENT
B4.006 LUBRICATE MECHANICAL GUN MOUNT EQUIPMENT AND
VERIFY MECHANICAL ADJUSTMENTS
B4.007 VERIFY THE OPERATIONAL TIMING OF GUN MOUNT
LOADING SYSTEM EQUIPMENT
B4.008 OPERATE THE VARIOUS TYPES OF MICROMETERS
B4.009 OPERATE A MULTIMETER, MEGGER, AND DIFFERENT
TYPES OF TORQUE WRENCHES
C. WEAPONS HANDLING/MAINTENANCE
C4.001 HANDLE, STOW, PACKAGE, UNPACKAGE, AND INVENTORY
NAVY GUN AMMUNITION, PYROTECHNIC AMMUNITION,
SMALL ARMS AMMUNITION
C4.002 STOW DEMOLITION CHARGES AND COMPONENTS
C4.003 ASSEMBLE AND USE ORDNANCE HANDLING AND
ASSOCIATED EQUIPMENT; PERFORM PREVENTIVE AND
CORRECTIVE MAINTENANCE ON ORDNANCE HANDLING
EQUIPMENT
C4.004 PREPARE ORDNANCE AND AMMUNITION FOR UNDERWAY
REPLENISHMENT
C4.005 PERFORM RECEIPT AND TRANSFER INSPECTIONS OF
GUIDED MISSILES
D. ORDNANCE/COMPONENT MAINTENANCE
D4.001 OPERATE GUN SYSTEM FUZE SETTING DEVICES; SET
POINT DETONATING PROJECTILE FUZES FOR EITHER
POINT DETONATION OR DELAY
D4.002 PREPARE AERODYNAMIC SURFACES FOR FLIGHT AND
STOWAGE
E. SMALL ARMS/SECURITY FORCES EQUIPMENT
E4.001 PERFORM MAINTENANCE ON LINE THROWING KIT AND
ADAPTERS
E4.002 INVENTORY, STOW, AND ISSUE SMALL ARMS AND
PYROTECHNIC PISTOLS
E4.003 LOAD, FIRE, AND UNLOAD THE FOLLOWING SMALL ARMS:
M-14 RIFLE, M-16 RIFLE, M-79 GRENADE LAUNCHER,
M1911A1 .45 CALIBER PISTOL, M-60D MACHINE GUN,
M2 .50 CALIBER MACHINE GUN, MK 19 MOD 3 40-MM
MACHINE GUN, REMINGTON 870 SHOTGUN, MOSSBERG 500
SHOTGUN, .38 CALIBER REVOLVER, 9-MM M9
E4.004 LOAD, FIRE, AND UNLOAD THE FOLLOWING PYROTECHNIC
DEVICES: AN-M8 PYROTECHNIC PISTOL, MK 79
PERSONNEL DISTRESS SIGNAL KIT
E4.005 LAUNCH THE MK 58 MODS 0 AND 1 MARINE LOCATION
MARKERS
E4.006 OPERATE THE MK 13 SMOKE AND ILLUMINATION SIGNAL
E4.007 OPERATE THE MK 1 MODS 0 AND 1 NAVY LIGHTS
E4.008 INVENTORY SHIP'S SELF-DEFENSE FORCE GEAR
E4.009 PERFORM ROUTINE MAINTENANCE ON THE FOLLOWING
SMALL ARMS AND GRENADE LAUNCHERS: .38 CALIBER
PISTOL, M1911A1 .45 CALIBER PISTOL, 9-MM M9,
M-14 RIFLE, M-16 RIFLE, REMINGTON 870 SHOTGUN,
MOSSBERG 500 SHOTGUN, M-60D MACHINE GUN, M2 .50
CALIBER MACHINE GUN, M-79 GRENADE LAUNCHER
F. ELECTRICAL/ELECTRONIC MAINTENANCE
F4.001 MAINTAIN, CLEAN, AND INSPECT COMPONENTS OF
ELECTRICAL EQUIPMENT
F4.002 SOLDER AND WIRE WRAP ELECTRICAL CONNECTIONS
F4.003 TEST THE OPERATION OF SOLID-STATE GUN MOUNT
ELECTRONIC CONTROL CIRCUITS
F4.004 TRACE THE STEPS IN THE PROCESS USED TO ISOLATE A
GUN SYSTEM CASUALTY TEST FOR SHORTS, GROUNDS,
AND CONTINUITY
F4.005 LOCATE THE VARIOUS TESTABLE POINTS ALONG AN
ELECTRICAL OR ELECTRONIC CIRCUIT, AND STATE THE
TYPE OF READINGS TO BE PERFORMED AT THESE POINTS
G. GENERAL MAINTENANCE (HYDRAULICS, PNEUMATICS, ETC.)
G4.001 MAINTAIN, INSPECT, AND PROPERLY USE HAND,
ELECTRICALLY POWERED AND PNEUMATICALLY POWERED
TOOLS
G4.002 REPAIR AND REPLACE HYDRAULIC PIPES, FITTINGS,
GASKETS, FASTENING HARDWARE, SEALS, SEALING
SURFACES, MATING AREAS, THREADS, AND FLEXIBLE
HOSES
G4.003 CUT, BEND, AND PREPARE PIPING AND TUBING FOR
LAUNCHING SYSTEMS
G4.004 PERFORM PREVENTIVE MAINTENANCE ON AND TEST
HYDRAULIC ORDNANCE EQUIPMENT AND DOCUMENT
RESULTS
G4.005 CLEAN, INSPECT, AND PERFORM
PREVENTIVE/CORRECTIVE MAINTENANCE ON GUN MOUNT
HYDRAULIC SYSTEMS
G4.006 CLEAN, INSPECT, AND PERFORM
PREVENTIVE/CORRECTIVE MAINTENANCE ON GUN MOUNT
PNEUMATIC SYSTEMS
G4.007 DETECT AND TREAT CORROSION
H. MAGAZINE AND FIRE SUPPRESSION SYSTEMS MAINTENANCE/OPERATIONS
H4.001 MONITOR AND RECORD MAGAZINE TEMPERATURE AND
HUMIDITY
H4.002 INSPECT MAGAZINES, PYROTECHNIC/READY SERVICES
LOCKERS
H4.003 OPERATE, PERFORM PREVENTIVE AND CORRECTIVE
MAINTENANCE ON MAGAZINE SPRINKLER SYSTEMS
I. TEST EQUIPMENT
I4.001 INVENTORY GENERAL-PURPOSE ELECTRONIC TEST
EQUIPMENT
K. TECHNICAL ADMINISTRATION
K4.001 USE ELECTRICAL SCHEMATICS TO IDENTIFY COMMON
ELECTRICAL/ELECTRONIC COMPONENTS AND THEIR
FUNCTIONS BY SCHEMATIC SYMBOLS
K4.002 TRACE THE FLOW OF SUPPLY VOLTAGE THROUGH THE GUN
MOUNT ELECTRICAL SUPPLY CIRCUITRY
K4.003 USE OPNAV AND NAVSEA INSTRUCTIONS AND
PUBLICATIONS THAT PERTAIN TO ORDNANCE SAFETY,
TRAINING, HANDLING, SECURITY, AND THE OPERATION
OF GUN MOUNTS AND GUIDED MISSILE LAUNCHING
SYSTEMS
L. SAFETY
L4.001 DON APPROPRIATE PERSONNEL PROTECTIVE EQUIPMENT
WHEN CLEANING UP HAZARDOUS MATERIAL
L4.002 DISPOSE OF USED AND EXCESS HAZARDOUS MATERIALS
GM2
A. WEAPON SYSTEMS OPERATIONS
A5.001 INSPECT ALIGNMENT ON GUN MOUNTS
A5.002 CONDUCT PREFIRING AND POSTFIRING CHECKS ON
GUIDED MISSILE LAUNCHING SYSTEMS
A5.003 CONDUCT A COMBAT SYSTEMS OPERABILITY TEST (CSOT)
ON GUIDED MISSILE LAUNCHING SYSTEMS USING AAW
AND ASW FIRE CONTROL INTERFACE
A5.004 ELECTRICALLY AND MECHANICALLY ALIGN GUIDED
MISSILE LAUNCHING SYSTEMS
A5.005 OPERATE THE DUD-JETTISONING EQUIPMENT FOR GUIDED
MISSILE LAUNCHING SYSTEMS
A5.006 MONITOR EMERGENCY FIRING AND DISPOSITION OF
MISFIRED ROUNDS
A5.007 VERIFY GUN MOUNT TRAIN AND ELEVATION RECEIVER
REGULATOR ACCURACY BY CONDUCTING GUN ORDER
TRANSMISSION CHECKS WITH THE GUN FIRE CONTROL
SYSTEM
A5.008 OPERATE THE SPECIAL TEST EQUIPMENT USED TO ALIGN
GUN MOUNTS
A5.009 INSTALL AND OPERATE A GUN MOUNT ERROR RECORDER
A5.010 OPERATE LAUNCHING SYSTEMS TEST EQUIPMENT
A5.011 CONDUCT SYSTEM TIMING CHECKS
B. WEAPON SYSTEM/COMPONENTS MAINTENANCE
B5.001 TEST, ADJUST, AND REPAIR COOLANT SYSTEMS AND
HEAT EXCHANGERS IN MISSILE LAUNCHING SYSTEMS
B5.002 TEST AND ADJUST LAUNCHING SYSTEMS
B5.003 VERIFY PROPER OPERATION AND ADJUSTMENT OF GUN
MOUNT MECHANICAL DEVICES; PERFORM CORRECTIVE
MAINTENANCE
B5.004 OPERATE GUN MOUNT FUZE-SETTING DEVICES
ASSOCIATED WITH THE DIFFERENT GUN MOUNTS
CURRENTLY IN SERVICE
B5.005 REMOVE, INSTALL, ADJUST, AND VERIFY ACCURACY OF
TRAIN AND ELEVATION INDICATORS
B5.006 PERFORM MAINTENANCE ON, ADJUST, AND TEST POWER
DRIVE SYSTEMS USED IN GUIDED MISSILE LAUNCHING
SYSTEMS AND GUN MOUNTS
B5.007 REPAIR AND REPLACE GML MECHANICAL COMPONENTS
B5.008 REPAIR AND REPLACE GUN MOUNT MECHANICAL
COMPONENTS
B5.009 PERFORM GUN BORE INSPECTION
C. WEAPONS HANDLING/MAINTENANCE
C5.001 INSPECT AND REPAIR MISSILE HANDLING EQUIPMENT
C5.002 INSPECT LAUNCHING SYSTEM MISSILE STRIKEDOWN
EQUIPMENT
C5.003 PERFORM ORDNANCE VERTICAL REPLENISHMENT
(VERTREP)
C5.004 TEST AND INSPECT WEAPONS HOISTS (HAND CHAIN,
ELECTRIC, PNEUMATIC, AND HYDRAULIC)
C5.005 PERFORM OPERATIONAL TEST OF ELEVATORS
C5.006 REPAIR, ADJUST, AND REPLACE WEAPONS ELEVATOR
COMPONENTS
D. ORDNANCE/COMPONENTS MAINTENANCE
D5.001 ASSEMBLE AND DISASSEMBLE MISSILES
E. SMALL ARMS/SECURITY FORCES EQUIPMENT
E5.001 INSTRUCT PERSONNEL IN GUN RANGE SAFETY
E5.002 CONDUCT SMALL ARMS QUALIFICATIONS (SECURITY
FORCE, RIBBONS, ETC.)
E5.003 CONDUCT SMALL FAMILIARIZATION (FAMFIRE)
F. ELECTRICAL/ELECTRONIC MAINTENANCE
F5.001 PERFORM PHASE, BALANCE, AND FEEDBACK ADJUSTMENTS
TO SERVO AMPLIFIERS USED IN GUIDED MISSILE
LAUNCHING SYSTEMS
F5.002 ANALYZE, REMOVE, INSTALL, ALIGN, AND ZERO THE
VARIOUS TYPES OF SYNCHROS USED IN GUN MOUNTS AND
GUIDED MISSILE LAUNCHING SYSTEMS
F5.003 TEST THE FOLLOWING ALARMS AND SENSING DEVICES:
OVER PRESSURE, HIGH VOLTAGE, LOW VOLTAGE, FILTER
CLOGGED, LOW SYNCHRO POWER, HIGH FLUID
TEMPERATURE
F5.004 REPLACE ELECTRONIC COMPONENTS AND MODULES
F5.005 TROUBLESHOOT AND REPAIR ELECTRONIC AND
ELECTRICAL CIRCUITS USING A LOGICAL SEQUENCE
F5.006 TEST, MONITOR, AND TROUBLESHOOT GUN MOUNT ALARMS
AND SENSORS: FILTER CLOGGED, HIGH TEMPERATURE,
GROUND DETECTOR, FUSE BLOWN INDICATORS, POWER
AVAILABLE INDICATORS, AND EQUIPMENT POSITION
INDICATORS AND INTERLOCKS
G. GENERAL MAINTENANCE (HYDRAULICS, PNEUMATICS, ETC.)
G5.001 REMOVE AND REPLACE COMMON HYDRAULIC SYSTEM
SEALS, TROUBLESHOOT AND REPAIR HYDRAULIC PUMPS
G5.002 INSPECT GUN MOUNT RECOIL, COUNTER RECOIL, AND
GAS EJECTOR
G5.003 TROUBLESHOOT, REMOVE AND INSTALL COMPONENTS IN
HYDRAULIC AND PNEUMATIC SYSTEMS OF GUIDED
MISSILE LAUNCHING SYSTEMS AND GUN MOUNTS
H. MAGAZINE AND FIRE SUPPRESSION SYSTEMS MAINTENANCE/OPERATIONS
H5.001 OPERATE, TEST, AND REPAIR MAGAZINE SPRINKLERS,
DELUGE, AND BOOSTER SUPPRESSION SYSTEMS
K. TECHNICAL ADMINISTRATION
K5.001 PLAN AND SUPERVISE AMMUNITION STOWAGE IN
SECURITY MAGAZINES AND READY SERVICE LOCKERS
K5.002 COMPILE MATERIAL SAFETY DATA SHEETS
K5.003 REVIEW WEIGHT TEST RENEWAL DATA
K5.004 UPDATE GUIDED MISSILE LOGS
K5.005 INTERPRET DRAWINGS (BLUEPRINTS, SCHEMATICS,
ETC.) WHILE TROUBLESHOOTING GMLS AND GUN MOUNT
COMPONENTS
L. SAFETY
L5.001 CONDUCT AN INSPECTION OF HAZMAT STOWAGE LOCKERS
GM1
A. WEAPON SYSTEMS OPERATIONS
A6.001 PERFORM LAUNCHER SYSTEM DYNAMIC TEST AND ANALYZE
RESULTS
A6.002 PERFORM GUN BARREL INSPECTION AND ANALYZE BARREL
WEAR DATA
A6.003 PERFORM GUN AND GMLS LOADING SYSTEM TEST AND
ANALYZE TIMING DATA
A6.004 PERFORM BATTERY ALIGNMENT ON GUN MOUNT AND GMLS
A6.005 DEVELOP AND CONDUCT GUN MOUNT AND GMLS CASUALTY
CONTROL DRILLS
B. WEAPON SYSTEMS/COMPONENTS MAINTENANCE
B6.001 INSPECT WEAPON/MISSILE LAUNCHING MECHANICAL,
HYDRAULIC, AND PNEUMATIC SYSTEMS CHECKS
B6.002 EVALUATE GUN MOUNT MECHANICAL SYSTEM OPERATION
AND DETERMINE THE NEED FOR REPAIR, OVERHAUL, OR
ADJUSTMENT
B6.003 SUPERVISE OVERHAULS AND ADJUSTMENTS TO MISSILE
LAUNCHING SYSTEMS AND HANDLING EQUIPMENT
B6.004 DETERMINE THE CIRCUMSTANCES THAT WOULD REQUIRE
THE RE-DEFINING OF FIRING CUTOUT ZONES
B6.005 DIAGNOSE ELECTRICAL AND ELECTRONIC MALFUNCTIONS;
SUPERVISE ELECTRICAL AND ELECTRONIC SYSTEMS
MAINTENANCE
B6.006 MONITOR ELECTRICAL/ELECTRONIC REPAIRS TO MISSILE
LAUNCHING SYSTEMS AND ASSOCIATED EQUIPMENT
B6.007 TEST AND REPAIR GUN MOUNT TRAIN AND ELEVATION
POWER DRIVES AND FUZE SETTER AMPLIFIERS
B6.008 INSTRUCT PERSONNEL ON THE MAINTENANCE AND
TESTING PROCEDURES USED WHILE WORKING ON A
MISSILE LAUNCHING SYSTEM AND ITS ASSOCIATED
EQUIPMENT
B6.009 REVIEW THE SOURCES OF TECHNICAL INFORMATION
AVAILABLE FOR ASSISTANCE IN THE PERFORMANCE OF
PREVENTIVE AND CORRECTIVE MAINTENANCE ON
ORDNANCE EQUIPMENT
C. WEAPONS HANDLING/MAINTENANCE
C6.001 MAINTAIN THE TRAINING RECORD REQUIREMENTS OF THE
NON-NUCLEAR AMMUNITION HANDLING QUAL/CERT
PROGRAM
C6.002 IMPLEMENT SAFETY PROCEDURES OF WORKING IN
MAGAZINE SPACES TO MAINTENANCE CREWS PRIOR TO
ENTERING ANY MAGAZINE
C6.003 SUPERVISE WEAPONS INVENTORY IN A MAGAZINE SPACE
C6.004 PERFORM SAFETY BRIEF TO PERSONNEL PRIOR TO ANY
HANDLING, TRANSFERRING, OR STOWAGE OF
AMMUNITION, MISSILES, OR MISSILE COMPONENTS
C6.005 REVIEW THE PUBLICATIONS THAT GOVERN MAGAZINE
MAINTENANCE AND UPKEEP
C6.006 REVIEW THE MINIMUM FREQUENCY AND SPECIAL
OCCASION REQUIREMENTS FOR SMALL ARMS AND
AMMUNITION INVENTORIES
C6.007 REVIEW THE SOURCES OF MAGAZINE SPRINKLER,
ORDNANCE SAFETY, AND GUN MOUNT MATERIAL
INSPECTION CRITERION
C6.008 SUPERVISE CREWS IN TRANSFERRING, HANDLING, AND
STOWING ORDNANCE
D. ORDNANCE/COMPONENT MAINTENANCE
D6.001 INITIATE SURVEYS AND DAMAGED SHIPMENT REPORTS
WITH SUPPLY DEPARTMENT
D6.002 CONDUCT OPERATION CHECKS ON THE GUIDED MISSILE
TRAINING ROUND (GMTR)
D6.003 CONDUCT INSPECTION ON EXPLOSIVE ORDNANCE ITEMS
FOR DAMAGE, AND MARK DAMAGED COMPONENTS
G. GENERAL MAINTENANCE (HYDRAULICS, PNEUMATICS, ETC.)
G6.001 SUPERVISE AND INSPECT HYDRAULIC AND PNEUMATIC
SYSTEMS REPAIRS, MODIFICATIONS, AND CHANGES TO
MISSILE LAUNCHING AND HANDLING SYSTEMS
G6.002 INSPECT, REPAIR/ADJUST, AND OVERHAUL GUN MOUNT
HYDRAULIC AND PNEUMATIC SYSTEMS; SUPERVISE
HYDRAULIC/PNEUMATIC SYSTEMS MAINTENANCE
G6.003 SUPERVISE MAINTENANCE CREWS ON PERFORMING
MAINTENANCE ON HYDRAULIC/PNEUMATIC EQUIPMENT OF
MISSILE LAUNCHING SYSTEMS AND ITS ASSOCIATED
EQUIPMENT
H. MAGAZINE AND FIRE SUPPRESSION SYSTEMS MAINTENANCE/OPERATIONS
H6.001 INVENTORY AND CHANGE SECURITY LOCKS AND
COMPONENTS
H6.002 CONDUCT TEST, OPERATION, AND CORRECTIVE
MAINTENANCE ON THE DRY MAGAZINE SPRINKLER
SYSTEM, CO2 FIRE SUPPRESSION SYSTEM, AND WATER
INJECTION SYSTEM
J. QUALITY ASSURANCE
J6.001 CONDUCT QUALITY ASSURANCE INSPECTIONS ON MISSILE
LAUNCHING AND HANDLING EQUIPMENT
J6.002 PERFORM QUALITY ASSURANCE INSPECTION
J6.003 SUPERVISE AND ESCORT INSPECTING PERSONNEL DURING
MAINTENANCE AND MATERIAL INSPECTIONS FOR
THOROUGHNESS AND DISCREPANCY INFORMATION
J6.004 REVIEW AND ANNOTATE DISCREPANCY TRENDS AND
PROPOSE CORRECTIVE ACTIONS DURING MATERIAL
INSPECTIONS
J6.005 PERFORM RECEIPT AND TRANSFER INSPECTIONS ON
ORDNANCE (OTHER THAN MISSILES)
K. TECHNICAL ADMINISTRATION
K6.001 MONITOR COMPLIANCE WITH THE PHYSICAL SECURITY
REQUIREMENTS FOR THE HANDLING AND STORAGE OF
CLASSIFIED MATERIAL
K6.002 MAINTAIN AMMUNITION LOT AND CONTROLLED EQUIPAGE
CARDS WITH ORDNANCE OFFICER
K6.003 INITIATE SURVEYS AND DAMAGED SHIPMENT REPORTS
K6.004 REVIEW THE LOG RECORDS ASSOCIATED WITH ORDNANCE
EQUIPMENT AND MAGAZINES, THEIR MAKEUP AND
INSPECTION REQUIREMENTS
K6.005 MAINTAIN THE CONVENTIONAL AMMUNITION INTEGRATED
MANAGEMENT SYSTEM (CAIMS) TRANSACTION REPORTING
REQUIREMENTS
K6.006 COORDINATE REPAIR AND CALIBRATION OF TEST
EQUIPMENT IN CONJUNCTION WITH SHIPBOARD
CALIBRATION FACILITIES AND IMA
K6.007 REVIEW WEIGHT TEST DATA FOR ASSIGNED HANDLING
EQUIPMENT
K6.008 REVIEW THE REQUIREMENTS FOR MAINTAINING MAGAZINE
LOAD AND STOWAGE PLANS
K6.009 PREPARE AMMUNITION TRANSACTION REPORTS
K6.010 PREPARE AND UPDATE AMMUNITION LOT AND LOCATION
CARDS
K6.011 PREPARE AND INVENTORY MASTER STOCK RECORDS CARDS
GMC
A. WEAPON SYSTEM OPERATIONS
A7.001 SUPERVISE THE ALIGNMENT OF GUN AND MISSILE
BATTERIES
A7.002 ANALYZE DISCREPANCY TRENDS AND DETERMINE
CORRECTIVE ACTION
B. WEAPON SYSTEMS/COMPONENTS MAINTENANCE
B7.001 INSPECT COMPLETED WEAPONS SYSTEMS MODERNIZATION
ORDALTS AND FIELD CHANGES
B7.002 COORDINATE SURFACE WEAPONS SYSTEMS OVERHAUL AND
REPAIR ON BOARD SHIPS AND AT INTERMEDIATE
MAINTENANCE ACTIVITY FACILITIES
C. WEAPONS HANDLING/MAINTENANCE
C7.001 REVIEW THE SOURCES GOVERNING ORDNANCE HANDLING
EQUIPMENT, INSPECTION AND WEIGHT TEST CRITERION
C7.002 CONDUCT ONLOAD AND OFF-LOAD OF MISSILES USING
WEAPONS HANDLING CHECKSHEETS
C7.003 CONDUCT ONLOAD AND OFF-LOAD OF AMMUNITION
C7.004 PREPARE LOADING AND STORAGE PLANS
C7.005 REVIEW THE REQUIREMENTS FOR THE MAINTENANCE OF
PQS AND QUAL/CERT TRAINING PROGRAM RECORDS
D. ORDNANCE/COMPONENT MAINTENANCE
D7.001 REVIEW THE REQUIREMENTS FOR MISSILE INSPECTION
AFTER CASUALTY WET DOWNS
E. SMALL ARMS/SECURITY FORCES EQUIPMENT
E7.001 DEVELOP AND MONITOR SSDF AND SECURITY ALERT
EXERCISES
E7.002 CONDUCT PHYSICAL SECURITY SURVEYS
H. MAGAZINE AND FIRE SUPPRESSION SYSTEMS MAINTENANCE/OPERATIONS
H7.001 CONDUCT TEST OPERATION ON THE DELUGE SYSTEM
H7.002 PERFORM MAGAZINE SPRINKLER SYSTEM INSPECTIONS
AND CERTIFICATIONS
J. QUALITY ASSURANCE
J7.001 PERFORM ACCEPTANCE INSPECTIONS ON MISSILES,
AMMUNITION, AND OTHER ORDNANCE
K. TECHNICAL ADMINISTRATION
K7.001 UPDATE SMALL ARMS LOGS, CUSTODY LOGS, AND
EXPLOSIVE KEY CONTROL LOGS
K7.002 DEVELOP AND REVIEW COMBAT SYSTEMS CASUALTY
CONTROL SHIPBOARD PACKAGES
K7.003 PREPARE PROCEDURAL GUIDES
Index
